Specification & Description

Receiver

Channel: 12 CH/ 6CHControl Types: Toggle, Momentary, LatchedDecode: Learning codeFrequency:433MHzPower Supply (Operating Voltage): DC 12VRelay: 10A/120VAC, 10A/277VDC

Transmitter

Channel: 12 CH/6 CHDistance: 100 meter(open/ideal) in theory, 10%-50% in reality(In open environment,receiver antenna outside the box)Encode: Fixed code, SolderingSize: 125mm x 49mm x 20mmPower Supply: 1 x 23A-12V battery

About 12CH Receiver:

Channel: 12 CHRadio Frequency: 433MHZOperating Voltage: DC12V or DC24VThe way of output:A. 1-12CH Momentary-----Set jumper ON "A&L"B. 1-12CH Latched----- Set jumper ON 1 PIN (Don't used jumper)C. 1-12CH Toggle-- --Set jumper ON "B&L" MomentaryPress the Transmitter button 1, the receiver relay 1th is ON, release button 1; the receiver relay 1th is OFF, the same as 2/3/4/5/6/7/8/9/10/11/12. 12CH are independent.TogglePress transmitter button 1 for 1 time, the receiver relay 1th is ON, press button 1 again, the receiver relay 1th is OFF, the same 2/3/4/5/6/7/8/9/10/11/12. 12CH are independent.LatchedPress transmitter button 1, the receiver relay 1th is ON, the relay 2/3/4/5/6/7/8/9/10/11/12 OFF.Press transmitter button 2, the receiver relay 2th is ON, the relay 1/3/4/5/6/7/8/9/10/11/12 is OFF.Press transmitter button 3, the receiver relay 3th is ON, the relay 1/2/4/5/6/7/8/9/10/11/12 is OFFPress transmitter button 4, the receiver relay 4th is ON, the relay 1/2/3/5/6/7/8/9/10/11/12 is OFF. …………….It also mean .Latched only can keep 1CH ON .and it will often have 1CH is ON.Learning way and steps:Learning Code:Input DC12V or DC24V for the Receiver, Press the Learning Button on the Receiver ,LED Indicator ON ,Release it, then press the Transmitter Button, Receiver LED Indicator flash for 3 time, it mean learning is successful. （Disconnect the power and connect again for used normal ）Clearing Code:Input DC12V or DC24V for the Receiver, press the learning button on the receiver and hold for about 8s until the Receiver LED indicator OFF, it mean the code have been cleared.

About 6CH Receiver Learning and cleaning Method:

Learning: Press the learning key, it means the controller putting in the learning state when the indicator goes ON, then please press any buttons of the remote control to transmit signals, the indicator will flash for 3 times after 1 second, then recover to normally OFF, which means successfully studied.After pressing any buttons of the remote control to transmit signal, the indicator didn't flash, 10 seconds later it still recovers to normally on, but it study unsuccessfully.Cleaning: Hold press learning button about 8 seconds, indicator from ON to OFF, then press remote receiver did not work, it means cleaning code successful.A: Signal non-lock (jog): press the NO.1 button of the remote control to learnB: Signal self-lock (self-lock): press the No.2 button to learn, each channel is independent of the othersC: Signal inter-lock: press the NO.3 button to learnD: 1CH-3CH is jog, 4CH-6CH is self-lock press the NO.4button to learnE: 1CH-3CH is jog, 4CH-6CH is inter-lock press the NO.5button to learnF: 1CH-2CH is jog, 3CH-6CH is inter-lock press the NO.6 button to learn

Pay attention:

The default setting of output way is momentary, press is on, release is off. If you need other output way can leave a message to change it for you before the delivery.We default is momentary.

Battery not included

Package includes

1 x Transmitter (Battery not included) 1 x Receiver