GT3582 GT35 Universal Turbocharger for all 4/6 cylinder 2.5L-6.0L up to 600HP

Note :  This is Updated Version Universal Application Turbo, so modification might be required for some vehicles.

Application：

Bigger HP Applications, perfect for all 4/6 cylinder and  2.5L-6.0L enginesfor Honda B16/B18, K20, H22, F22 Enginesfor Nissan SR20DET, RB20/25,for Toyota 1JZ/2JZ, 7MGTE.Also Works for Twin Turbos Applications for GM for SBC, for LSx,for Ford 4.6, 5.0 Engines

Product Specific：Exhaust (Turbo Manifold) Flange： T3 FlangeExhaust (Downpipe) Flange： 4 BoltWastegate： External WastegateBearing Type:    Floating BearingTurbo Width:  240mmTurbo Height:  230mmTurbo length： 260mmMaximum PSI value： 22Horse Power： Boost Horse Power up to 600HPCooling Type： Water + OilMax HP： UP to 600h

Compressor：Compressor Trim： 57Inducer Diameter： 61.5 mmExducer Diameter： 81.5 mmCompressor A/R： 0.7

Turbine：Turbine Trim： 84Inducer Diameter： 68 mmExducer Diameter： 62.4 mmTurbine A/R： 0.63Compress Inlet Size(Air intake):    4 inch (103.5mm)Compressor Outlet Size:   2.5 inch (63.6mm)Wastegate：  External WastegateOil feed/inlet:    M10*7/16-24Oil drian/outlet: 2*M8*1.25water inlet/outlet:   M14* 1.5Maximum PSI：22

Condition:   100% Brand NewWarranty： 2 YearsAccessories:  You will get exactly as shown in the picture above

Product Material:1. Turbine Housing ：Iron QT450-10 Shell2. Steel Turbine Wheel：K418 Alloy3. Compressor housing：ZL104 Aluminum4. Compressor Wheel / Blades： Cast Aluminium

Notice:

* Replace, repair or reconnect air cleaner element per manufacturer's manual to avoid compressor wheel damage. 

* Make sure the oil drain line is lower than the turbo itself. 

* Gasoline car must install a water cooling device to avoid overheating. 

* Ensure exhaust outlet are well sealed by welding.

* To protect the turbochager and your car engine, Air filter is necessary. 

NOTE： Lacking of oil will casue turbocharger shaft play and damage , please adjust your oil pressure & make sure turbochager is fully lubricated.

Tips before installing:1. Replace the air filter: if the if the air filter is not replaced may cause the compressor wheel damage. 2. Replace the engine oil: Because floating bearing and turbocharger will be damaged by impurities in the old oil. 3. After large overhaul, the engine cannot be replaced with a new turbocharger because there are too much impurities in oil after overhauling which will damage the replacement turbocharger immediately. Please run the old turbocharger for 7-10 days and then replace to new turbocharger and new engine oil.

Q&A:Q：Does this come with everything you need to install?A：It's just the Turbo and Gaskets. You'll need an oil feed and drain lines, Turbo manifold, Downpipe, Boost Controller(if you want to run higher boost than wastegate pressures), an ecu tune, Piping and Intercooler. There's probably some other things I'm missing but those are most of the major components you'll need

Q：What is the oil feed thread and pitch, and what is the cold side exit/inlet diameters for the gt35 version? What is the cold side inlet size ？A：the oil feed thread size : 16/7-18 fitting; the cold side inlet size: M14X1.5